MILK GARDEN

Remember this garden bed I was working on?

The plants have finally grown in in my “milk garden”, so I can show what the finished flower bed looks like.
The idea is that the milk can has tipped over and spilled out the “milk”; in this case, plants. In keeping with the theme, I also have my “Ice Cream Sundae” totem in front of the Planter Bench made from an old metal bed frame.
For the milk, I planted some Nettle, which is a perennial, but because they won’t fill in for a couple of years, so I filled in with Dusty Miller, which is an annual in my area. The Dusty Miller is much whiter than the Nettle.

From Pinterest

This was the inspiration for my garden bed, but I wanted to use white foliage plants instead of flowers, so that the effect would be long lasting. I suppose if I wanted to spend tons every year on annuals, I could have gone with flowers, but I just can't justify that cost.

I had a milk can that I was no longer using as a plant holder, so it came to this garden bed. In the inspiration photo, they used a much smaller can, so I can see where they could get away with less cost on the flowers. I left the can as well as the bench rusty and peeling paint.

There is flat stone around the garden bed, so I can mow right up to it. In the non-milk area, I have planted Ajuga, but it will be a while before that fills in, so I covered the bare areas with wood chips. Underneath this all is heavy plastic from a silage bag, with the white side up. I guess, once the plants filled in, it didn’t really make much difference if it was black or white, but before the white blended a little better. Behind the planter bench, I planted Dahlia bulbs. They won’t flower for another month or so, but they should get at least as tall as the back of the bench and will have dark red flowers. It is a very beautiful Dahlia that I’ve grown for years.

I am pleased with how it turned out.

Planter Bench From Metal Bed Frame

Remember my plans to make a planter bench out of an old metal bed frame?

Well, here it is:

It’s part of my new front garden bed. That’s my ice cream sundae totem just to the left.
Basically, what I did was to cut the footboard in half; but it was a little too deep for what I wanted, so I cut off another 6” or so. I was going to prime it and paint it, but decided I wanted a rusty kind of look. Problem was, I had used corner braces to connect it and they were shiny silver. I sprayed the braces and all the nuts and bolts with black paint and then just kind of lightly went over the rest of the bench, kinda feathering it out from the painted hardware. Turned out ok.

Look at that, a spider has already built a web on it. HA!

  I cut the rails to fit the width of the headboard, Gary welded it back together for me and I used the original brackets to attach it across the front. I cut a piece of the other rail to fit across the back and he welded that to a brace that was already there. I did; however have to cut the side pieces down to match up with that back brace. It was too tall on the sides anyway. This looks much better. 

Front

  Back

I stuck a solar light in there, but I keep forgetting to go out front at night to see if it’s even working.

I cut pieces of deck board to fit between the rails and left spaces to slip some oblong planters in. There was just the right space for the planters and I didn’t have to rip any boards down to make it work. How cool is that?! Again I originally was going to paint these boards, but decided to let them weather naturally. Of course for this year, they are going to be golden instead of gray, but it’ll do.

See how the boards fit nicely into the bed rails?

Finally, I drilled holes into the top of the backboard to put in some plant hangers that I cut and bent out of a 1/4” rod. I have Dahlias planted behind the bench, but they are only about 6” tall at this point. I can hardly wait for the plants to fill in some, but it’s looking pretty decent already.

The planter hangers I just left to rust.

I am very pleased at how it turned out.
Stay tuned for the complete reveal of the whole garden bed in an upcoming post.

Technorati Tags: DIY,Outdoor Design,Recycle

Linking to: 

{Dot}{Dot}{Dot}

Ice Cream Sundae Totem

This is the totem I made for my new garden bed. I used a small green flower vase inverted to serve as the “holder” to slip over the post (ice cream cup stem). I found these great posts at Menards, which are 60” long and are plastic coated metal hollow rods. I only used 30” for this project, so I have the other 1/2 to use for another totem. I cut them off with a chop saw, but a hacksaw would work as well.

Here’s how the totem stacked up:

On top of the vase, I adhered a yellow dinner plate and yellow salad plate right side up (bowl of ice  cream cup), followed by a sort of pumpkin shaped white canister upside down, that I had used to keep my utensils in on the kitchen counter (scoop of ice cream). Next came a fluted carnival glass plate we received as a wedding gift 35 years ago. I very seldom used it, except to put candy in once or twice. This also was upside down (caramel topping). A clear cut glass bowl, also upside down came next (whipped cream) and it was topped off with a metal cupola, I guess you would call it, from a lantern candle holder that I made into a solar patio lantern. I spray painted the cupola red to simulate a cherry. I finished off my sundae with a tablespoon, which I cut off 1/3 of the bowl, with a chop saw, and glued to the bottom of the whipped topping.

These are the steps I followed:

First, I marked where the pieces needed to go by tracing them with a marker. I then “sanded” these markings off, with a little over each way;

with a dremel, fitted with a diamond tip bit. This made short work of the task of roughening the areas for the glue to adhere to.

Secondly, I cleaned the area to be glued well with alcohol and a rag.

Starting with the plates, I next applied clear silicon adhesive sealant, liberally to one surface and glued them together. I glued all the top pieces, above the vase, the same day. To attach the spoon, I hammered the bowl of the spoon a little flatter, to be close to the same arc as the whipped topping bowl. I then glued it on with the silicon adhesive and propped it against a tall object until it was set. Worked out ok, so far, but we’ll see how it handles the elements. I then waited a day and turned the piece upside down , placing it on a roll of painter’s tape, so the “cherry” was in the hole; therefore, resting mostly level. I then glued the vase, upside down to the bottom of the dinner plate and waited another day before tipping it over and putting it on the post which I had pounded into the ground.  I used Loctite clear silicon adhesive sealant, but I’m sure there are other brands as well. 

So, here is my ice cream sundae in the new garden bed. It is next to the planter bench I made out of an old metal bed frame. More to come on that another time.

Technorati Tags: DIY,Outdoor Design,Recycle

Address Me As Ms. DIY, If You Please

Just a little project I completed today.

   

I’ve had these cut out for about a month now, but just waiting for the weather to be warm enough to apply. I bought this vinyl off Ebay and it is supposed to be sign vinyl, so we’ll see how it lasts outdoors. It very little protected under the eaves, and it will get direct sun for part of the day, as well as rain. This will be a good test to see if I want to do something bigger outdoors.

I washed the area and prepped it with alcohol before applying the vinyl. It seems to have adhered very well.

Here’s  the full effect:

It doesn’t look like it, because of the slight angle of the picture, but it is centered under the light fixture.        

I think it looks pretty nice.

Now I just have to wash the rest of the siding and maybe repaint those light fixtures.

Have A Nice Afternoon!
Linking to:
Sew Many Ways

Homemaker On A Dime

Technorati Tags: Silhouette,DIY,Outdoor Design

Garden Work….. Finally! A New Flower Bed

The weather has finally been warm enough and dry enough, that I could do some garden work. Not vegetable gardening yet, too cold for that. My tomato plants are still in the make shift greenhouse I fashioned out of hay bales, cattle panels and tarps. Seems to be working ok, but it would be nice to get the plants in the ground.
The garden work I’m referring to is a new flower bed that’s going in the front yard. I worked about 2 hrs. on it yesterday and about 1 1/2 hrs. today.

This is what I have done so far:

   

I’m not sure if you can tell, but the lawn is on a slope here. That figures into my bed perfectly.

The first day, I collected the flat rock that will be the border of the bed, laid out the bed, and dug about 1/4 of the sod out. That was enough for one day, since I’m “old”. J/K, the fact is that’s about all my injured leg could handle for one day. the good news is all that stretching  should help my leg to heal faster.

Today, I finished digging out the rest of the sod. I had five loads of sod that I dug out.

And what did I do with all that sod, you ask? I dumped it in a low area in front of the shed that always fills with water when it rains. It would be a great place for a rain garden, but it’s also an area where the guys tend to park a lot of the farm equipment during the summer months.  Oh, how I would love a rain garden though. Maybe someday, if we ever move to a different home for retirement.

   

So here’s my inspiration for what I envision for the new flower bed:

 

I found this pic on Pinterest. I already have a milk can I can use and I plan to put my metal bed frame planter bench in the vignette also, as soon as I have it built. For the “spilled milk”, I bought some Dusty Miller plants. Hopefully, they will be white enough. The finishing touch will be a tea cup bird feeder.

On another garden related matter, I transplanted some ferns I got from a friend’s property. I transplanted some last year and they came through the winter fine, so I got some more this year. Believe it or not, these ferns were only as tall as the short ones in the pic, just a few days ago (those are the ones I transplanted last year). They seem to grow about 2'” every day!

They are a pretty tough fern. If you look closely at the pic on the bottom below, you’ll see some green coming in an otherwise dead looking plant, as in the pic on the top.

The Autumn Fern I bought from Menards last year, on the other hand does look like it has bit the dust. In a cursory inspection, I could not find any signs of returning growth. The label states that there is a 1 year guarantee, so I’ll have to hunt up my receipt and check it out. I don’t know if I have to take the dead plant back or if I just need the receipt. I will have to call and find out.

 

Have A Great Evening!

Technorati Tags: Outdoor Design,DIY,Garden